Remarks of Plastic Extrusion Machine Operation and Mataince
Protection function
During working, if the saw is in the movable range, but the profile is not cut off and the saw can not be back; move on, the route switch SQ2 would be on and send signal, the saw would stop working. And then make the back electromagnetic YA8 moving. Move on if you can not back the saw due to air err, and the route switch SQ1 will send signal, which made the whole line stop.
2.5.6 Remarks
During working, if err happens, you can press "Emergency Stop" in time, then the whole line stops.
2.6 machine maintenance and protection
Always check power voltage
Always check working compress of every compress watch, check whether the pipes leak oil or water.
Oil added into oil fog set regularly
You should maintain the pneumatic element in regular time to ensure pneumatic element running is ok. So you should discharge the ice deposit of filtration transparent receptacle and make viscosity to be over 3a B50 lubrication oil. You drip a little lubrication oil into filter.
Always check the working compress of per dashboard and whether pipe is leaking water and air or not, if it occurred and you must eliminate in time.
chain wheel drive part of haul-off unit adopt the 20# engine oil, artificial lubrication in regular time and you check the gear lubrication, clean it or change it.
Guild pillar of saw support should be often clean.
You should often check whether E-motor rotation and belt is loose or not.
you should often check whether every connecting fixed part is loose or not
You should maintain vacuum pump and water pump seriously according to the relative instructions
guiding pillar of saw shelf shall be always cleaned
lubrication and hoisting/lifting installation see relative plans
During working, if the saw is in the movable range, but the profile is not cut off and the saw can not be back; move on, the route switch SQ2 would be on and send signal, the saw would stop working. And then make the back electromagnetic YA8 moving. Move on if you can not back the saw due to air err, and the route switch SQ1 will send signal, which made the whole line stop.
2.5.6 Remarks
During working, if err happens, you can press "Emergency Stop" in time, then the whole line stops.
2.6 machine maintenance and protection
Always check power voltage
Always check working compress of every compress watch, check whether the pipes leak oil or water.
Oil added into oil fog set regularly
You should maintain the pneumatic element in regular time to ensure pneumatic element running is ok. So you should discharge the ice deposit of filtration transparent receptacle and make viscosity to be over 3a B50 lubrication oil. You drip a little lubrication oil into filter.
Always check the working compress of per dashboard and whether pipe is leaking water and air or not, if it occurred and you must eliminate in time.
chain wheel drive part of haul-off unit adopt the 20# engine oil, artificial lubrication in regular time and you check the gear lubrication, clean it or change it.
Guild pillar of saw support should be often clean.
You should often check whether E-motor rotation and belt is loose or not.
you should often check whether every connecting fixed part is loose or not
You should maintain vacuum pump and water pump seriously according to the relative instructions
guiding pillar of saw shelf shall be always cleaned
lubrication and hoisting/lifting installation see relative plans
err | cause | Treatment way |
Unable to work of the whole line | Power supply broken | Check the power |
Fuse broken | Change the inner part | |
Touching unit broken | Check loop line, change fusing unit | |
Unable to work of the water loop pump | Thermo relay | Check the motor load |
Touching unit broken | Change | |
Fuse broken | Check loop line, change | |
Unable to work of the cutting machine | No. calculator out of control | Check whether the signal outlet or not |
Relay for delay broken | change | |
Touching unit broken | change | |
Unable to work of the drawing machine | Speed adjustor broken | change |
Touching unit broken | change | |
Air system err | Air valve of electromagnet broken | change |
Relay broken | change | |
Route switch out or control | Adjust or change |
Previous:
Our Service
